Material Test Certificates

    Material Test Certificates

    What the certificate says, how it is numbered, and how to read one

    Documentation

    A Certificate, Not Just a Pass Mark

    An internal inspection record proves to the foundry that a casting passed. A Material Test Certificate proves it to the person receiving the goods, months later, in another country. For a procurement engineer the certificate is often the only evidence that survives the shipment, so it is treated as part of the product rather than as paperwork attached to it.

    Every batch dispatched by Sri Gnanamurugan Foundry is issued a Material Test Certificate in the BIS Annexure-I format under IS 210:2009, carrying the chemical composition and mechanical results measured on that batch.

    What Is on the Certificate

    The layout follows the BIS Annexure-I format. In substance, five things are reported for the batch:

    • —Chemical composition from spectrometer analysis of that heat
    • —Mechanical properties measured on the universal testing machine
    • —Hardness values for the batch
    • —The grade and the standard it is certified against (IS / EN / ASTM / DIN)
    • —Batch number and certificate number, so the document traces back to the run

    Certificates are numbered by financial year, which keeps the sequence meaningful across years instead of resetting or running into an ambiguous five-digit series. The number is what makes the document traceable: from it, the batch and the production run that produced it can be identified.

    Reading One as a Buyer

    Four checks catch nearly every problem that a certificate can reveal.

    The grade matches the drawing

    Check that the certified grade is the one you specified, not its nearest neighbour. This is where cross-standard confusion usually shows up.

    The standard and test bar are named

    A tensile figure is only meaningful next to the test bar size and the standard it was taken under, because both change the number.

    The numbering ties to your delivery

    Certificate and batch numbers should let you go from a casting on your floor back to the heat that produced it. Keep the certificate with the goods inward record.

    Values clear the minimum, not just meet it

    A result sitting exactly on the minimum is worth a conversation. Margin is a better indicator of process control than a pass mark.

    Where the Numbers Come From

    Chemical composition is measured on the spectrometer, and for every heat it is measured before pouring. That timing is what makes the number useful: a heat can still be corrected while it is liquid, so the certificate reports a composition that was actively controlled rather than one discovered afterwards.

    Mechanical properties come from test bars pulled on the universal testing machine, with hardness measured separately. Where the application depends on graphite form or matrix — typically ductile iron — an optical microscope with an image analyser is used to check microstructure rather than inferring it from chemistry alone.

    Moulding sand is tested in house for moisture, permeability and strength. That is not reported on the casting certificate, but it is why dimensional consistency holds across a batch: surface finish and dimensional accuracy are decided partly by the mould, not only by the metal.

    The grade designations and their equivalents are listed on the iron casting grades page.

    Documentation Beyond the Standard Certificate

    Some quality plans ask for more than the standard Annexure-I certificate. Where that is the case, the requirement is best raised with the enquiry rather than after the order, because traceability requirements affect how a batch is kept together and documented during production, not only what is printed at dispatch.

    Send the drawing, the grade, the quantity and the documentation requirement together and the quotation comes back with the standard the work will be certified against.

    MTC FAQ

    Certificate Questions

    What buyers ask about test certificates, traceability and what the document proves.

    Do you issue a Material Test Certificate with every batch?

    Yes. Every batch is issued a Material Test Certificate in the BIS Annexure-I format under IS 210:2009, carrying the chemical composition and mechanical test results measured on that batch, with financial-year certificate numbering so a certificate can be traced back to the production run it covers.

    What are the chemical and mechanical results based on?

    Chemical composition comes from spectrometer analysis of the heat, taken before pouring so the metal can still be corrected. Mechanical properties come from test bars pulled on the universal testing machine, with hardness measured separately, and microstructure checked on an optical microscope with image analyser where the application depends on graphite form or matrix.

    Can a certificate be traced back to a specific casting batch?

    Yes. Certificates carry both a batch number and a certificate number, numbered by financial year, which together identify the production run behind the goods. Keeping the certificate with the goods-inward record is what makes that traceability usable later if a question arises on the shop floor.

    Does the certificate cover ductile (SG) iron as well as grey iron?

    Yes. The format is used for both families. For SG iron castings to IS 1865 the certificate reports elongation alongside tensile strength, because a ductile grade is specified as a pair - SG 500/7 means 500 MPa minimum tensile with 7% minimum elongation - and a tensile figure alone would not identify the grade.